📄 Full Manual

You can download the manual here.

📦 WHAT’S INCLUDED

• Charger
• Pedals (left & right)
• Reflectors + mounts
• Headlight
• Hex key set
• Wrench
• Grease
• Spare derailleur hanger
• Stickers & accessories
• Manuals

🧩 PRODUCT OVERVIEW

Main components:

• Display + control pad
• Hub motor (500W)
• Battery (removable)
• Brakes (front & rear)
• Drivetrain (chain, derailleur, cassette)
• Wheels and tires
• Headlight + indicators
• Throttle

⚙️ FULL SETUP & ASSEMBLY

Key Steps

1. Unbox bike and remove packaging
2. Rotate and align stem
3. Install handlebars:
   • Align center markings
   • Tighten to ~6 Nm
4. Install front wheel:
   • Ensure rotor is inside brake caliper
   • Tighten axle to 35–45 Nm
5. Align handlebars with front wheel
6. Install pedals:
   • Right = clockwise
   • Left = counterclockwise
   • Torque: ~35 Nm
7. Install motor protection guards
8. Inflate tires:
   • 35–50 PSI
9. Adjust seat height and angle
10. Install headlight and connect cable

👉 Always check all bolts, alignment, and cables before riding

🔋 BATTERY & CHARGING

Charging Steps

1. Turn battery OFF
2. Open charging port
3. Connect charger to battery
4. Plug into outlet
5. Wait until fully charged
6. Disconnect (wall first, then battery)

Charging Indicators

• Red = charging
• Green = fully charged

Charging Rules (CRITICAL)

• Charge between 0°C – 40°C
• Charging time: 5–6 hours
• Do NOT charge more than 12 hours
• Do NOT leave unattended
• Use original charger only
• Charge on hard surface (concrete/brick)
• Do NOT cover charger

Battery Removal (Display Unlock System)

1. Turn bike ON
2. Press + and – together
3. Select Battery Lock
4. Unlock → battery pops out
5. Remove manually

Battery Installation

• Insert battery firmly
• Push until you hear CLICK
• Ensure no gaps
• Confirm locked

⚠️ If installed incorrectly → Error E140

Battery Storage

• Store at ~75% charge
• Temperature: 0°C – 40°C
• Check monthly

STOP USING IF:

• Overheating
• Smell or smoke
• Leakage
• Deformation

🎮 CONTROLS & OPERATION

Power

• Hold power button

Lights

• Hold “+” for 3 seconds

Assistance Levels

• ECO / SPORT / TURBO / BOOST
• Adjust with “+ / –”

WALK MODE

• Hold “–”

HOLD FUNCTION

• Prevents rollback on hills (auto 30s hold)

CRUISE CONTROL

Conditions:

• Speed > 10 km/h
• Battery > 15%
• Assist mode active

BOOST MODE

• Temporary power boost
• Max 30 seconds
• Cooldown: 5 minutes

TURN SIGNALS

• Use directional buttons
• Press again to turn off

DISPLAY DATA

• Speed
• Battery
• Assist level
• Trip
• Range
• ODO
• Time

⚙️ MAIN MENU FEATURES

Access: Hold + and –

Includes:

• Clear Trip
• Battery Lock
• Bike Lock
• Units (km/h ↔ mph)
• Brightness
• Auto Power OFF
• Password
• System Info
• Date & Time
• App Connection

🔒 SMART FEATURES

Aventon App

• Connect via QR code
• Remote lock/unlock
• GPS tracking
• Theft alerts
• Ride stats

🛵 HOW TO RIDE

1. Turn bike ON
2. Select assist level
3. Start pedaling or use throttle
4. Shift gears as needed
5. Use brakes to stop

⚙️ PRE-RIDE CHECKLIST

Before EVERY ride:

• Brakes working
• Tires inflated (35–50 PSI)
• Battery charged & locked
• No loose bolts
• Lights working
• Cables connected

🔧 MAINTENANCE

Regular Checks

• Brakes and pads
• Chain and drivetrain
• Tires and wheels
• Bolts and hardware
• Electrical system

Service Intervals

• Before every ride → inspection
• Weekly → basic check
• Monthly → adjustments + lubrication
• Every 6 months → full service

⚠️ SAFETY GUIDELINES

MUST DO

• Wear helmet
• Follow local laws
• Inspect bike before riding

DO NOT:

• Ride under influence
• Ride in heavy rain
• Modify components
• Perform jumps or stunts

Wet Riding

• Reduce speed
• Brake earlier

Night Riding

• Use lights
• Wear reflective gear

🚨 WARNING CODES (FROM MANUAL)

⚡ ERROR CODES (FROM MANUAL)

⚠️ FINAL NOTES

• Stop riding if error appears
• Do NOT override safety systems
• Increased wear is normal on e-bikes
• Service major faults professionally

https://www.youtube.com/watch?v=twQ3gr9Ytm8